Raspberry Pi/Zero 2W/Ubuntu/24.04

lsblk :' sdb 8:16 1 29.8G 0 disk ├─sdb1 8:17 1 512M 0 part /media/shahed/system-boot └─sdb2 8:18 1 29.3G 0 part /media/shahed/writable '	ls -alh /media/${USER}/system-boot/{ssh,{config,cmdline}.txt} :' -rw-r--r-- 1 shahed shahed 170 Dec 30 01:03 /media/shahed/system-boot/cmdline.txt -rw-r--r-- 1 shahed shahed 1.8K Dec 29 21:13 /media/shahed/system-boot/config.txt -rw-r--r-- 1 shahed shahed 0 Dec 29 17:45 /media/shahed/system-boot/ssh '
ls -lah /media/${USER}/writable/etc/netplan/ :' total 12K drwxr-xr-x 2 root root 4.0K Dec 30 08:29 . drwxr-xr-x 108 root root 4.0K Dec 29 20:55 .. -rw------- 1 root root 262 Dec 29 17:22 50-cloud-init.yaml '	ls -lah /media/${USER}/writable/etc/udev/rules.d/ :' total 72K drwxr-xr-x 2 root root 4.0K Aug 6 01:00 . drwxr-xr-x 4 root root 4.0K Dec 29 20:47 .. -rw-r--r-- 1 root root 62K Aug 6 01:00 70-snap.snapd.rules '
system-boot » config.txt cat /media/${USER}/system-boot/config.txt && echo <<-'TXT' [all] arm_64bit=1 kernel=vmlinuz cmdline=cmdline.txt initramfs initrd.img followkernel # Enable the audio output, I2C and SPI interfaces on the GPIO header. As these # parameters related to the base device-tree they must appear *before* any # other dtoverlay= specification dtparam=audio=on dtparam=i2c_arm=on dtparam=spi=on # Comment out the following line if the edges of the desktop appear outside # the edges of your display disable_overscan=1 # If you have issues with audio, you may try uncommenting the following line # which forces the HDMI output into HDMI mode instead of DVI (which doesn't # support audio output) #hdmi_drive=2 # Enable the KMS ("full" KMS) graphics overlay, leaving GPU memory as the # default (the kernel is in control of graphics memory with full KMS) dtoverlay=vc4-kms-v3d disable_fw_kms_setup=1 # Enable the serial pins enable_uart=1 # Autoload overlays for any recognized cameras or displays that are attached # to the CSI/DSI ports. Please note this is for libcamera support, *not* for # the legacy camera stack camera_auto_detect=1 display_auto_detect=1 # Config settings specific to arm64 dtoverlay=dwc2 [pi4] max_framebuffers=2 arm_boost=1 [pi3+] # Use a smaller contiguous memory area, specifically on the 3A+ to avoid an # OOM oops on boot. The 3B+ is also affected by this section, but it shouldn't # cause any issues on that board dtoverlay=vc4-kms-v3d,cma-128 [pi02] # The Zero 2W is another 512MB board which is occasionally affected by the same # OOM oops on boot. dtoverlay=vc4-kms-v3d,cma-128 [cm4] # Enable the USB2 outputs on the IO board (assuming your CM4 is plugged into # such a board) dtoverlay=dwc2,dr_mode=host [all] TXT system-boot » cmdline.txt cat /media/${USER}/system-boot/cmdline.txt && echo :' console=serial0,115200 multipath=off dwc_otg.lpm_enable=0 console=tty1 root=LABEL=writable rootfstype=ext4 rootwait fixrtc cfg80211.ieee80211_regdom=MY '

SD Card » Pre-Boot

SD Card » Pre-Boot

system-boot » config.txt cat <<'INI' | tee -a /media/${USER}/system-boot/config.txt >/dev/null dtoverlay=dwc2 # Enable Heartbeat LED dtparam=pwr_led_trigger=heartbeat dtparam=act_led_trigger=heartbeat INI lsmod | grep -E 'dwc2|g_ether' dmesg | grep -E 'dwc2' sudo dtoverlay dwc2 system-boot » cmdline.txt # modules-load=dwc2 cat <<'INI' | tee /media/${USER}/system-boot/cmdline.txt >/dev/null console=serial0,115200 multipath=off dwc_otg.lpm_enable=0 console=tty1 root=LABEL=writable rootfstype=ext4 rootwait modules-load=dwc2 fixrtc cfg80211.ieee80211_regdom=MY INI # modules-load=dwc2,g_ether cat <<'INI' | tee /media/${USER}/system-boot/cmdline.txt >/dev/null console=serial0,115200 multipath=off dwc_otg.lpm_enable=0 console=tty1 root=LABEL=writable rootfstype=ext4 rootwait modules-load=dwc2,g_ether fixrtc cfg80211.ieee80211_regdom=MY INI # modules-load=dwc2,g_ether # g_ether.host_addr=12:a5:cf:42:92:fd # g_ether.dev_addr=5e:bc:ca:27:92:b1 cat <<'INI' | tee /media/${USER}/system-boot/cmdline.txt >/dev/null console=serial0,115200 multipath=off dwc_otg.lpm_enable=0 console=tty1 root=LABEL=writable rootfstype=ext4 rootwait modules-load=dwc2,g_ether fixrtc cfg80211.ieee80211_regdom=MY g_ether.host_addr=12:a5:cf:42:92:fd g_ether.dev_addr=5e:bc:ca:27:92:b1 INI writable » 10-usb-wan.yaml ls -lah /media/${USER}/writable/etc/netplan/ cat <<'YML' | /media/${USER}/writable/etc/netplan/10-usb-wan.yaml >/dev/null --- network: version: 2 renderer: networkd ethernets: usb0: dhcp4: false addresses: - 192.168.10.2/24 routes: - to: default via: 192.168.10.1 nameservers: addresses: - 192.168.10.1 - 8.8.8.8 optional: true YML sudo chmod 600 /media/${USER}/writable/etc/netplan/10-usb-wan.yaml sudo netplan try --timeout 60 sudo netplan generate sudo netplan apply sudo ip add show usb0 ping -c3 192.168.10.1 ping -c3 192.168.10.2 writable » 99-usb-gadget.yaml ls -lah /media/${USER}/writable/etc/netplan/ cat <<'YML' | sudo tee /media/${USER}/writable/etc/netplan/99-usb-gadget.yaml >/dev/null --- network: version: 2 renderer: networkd ethernets: usb0: dhcp4: no addresses: - 192.168.8.2/24 optional: true YML sudo chmod 600 /media/${USER}/writable/etc/netplan/99-usb-gadget.yaml sudo netplan try --timeout 60 sudo netplan generate sudo netplan apply sudo ip add show usb0 ping -c3 192.168.8.1 ETH_USB0="$(ip -o link show | grep '12:a5:cf:42:92:fd' | awk -F': ' '{print $2}')" sudo ip addr add 192.168.8.1/24 dev "${ETH_USB0}" sudo ip link set "${ETH_USB0}" up sudo ip addr show "${ETH_USB0}" ping -c3 192.168.8.2 ping -c3 192.168.8.1