Raspberry Pi/5 16GB/Debian/13

lsblk :' sdb 8:16 1 29.8G 0 disk ├─sdb1 8:17 1 512M 0 part /media/shahed/bootfs └─sdb2 8:18 1 29.3G 0 part /media/shahed/rootfs '	ls -alh /media/${USER}/bootfs/{ssh,{config,cmdline}.txt} :' -rw-r--r-- 1 shahed shahed 176 Jan 1 1980 /media/shahed/bootfs/cmdline.txt -rw-r--r-- 1 shahed shahed 1.3K Dec 4 22:40 /media/shahed/bootfs/config.txt -rw-r--r-- 1 shahed shahed 0 Jan 8 22:30 /media/shahed/bootfs/ssh '
ls -lah /media/${USER}/rootfs/etc/netplan/ :' total 16K drwxr-xr-x 2 root root 4.0K Oct 17 16:18 . drwxr-xr-x 133 root root 12K Dec 4 22:50 .. '	ls -lah /media/${USER}/rootfs/etc/udev/rules.d/ :' total 12K drwxr-xr-x 2 root root 4.0K Dec 4 22:41 . drwxr-xr-x 4 root root 4.0K Dec 4 22:39 .. -rw-r--r-- 1 root root 337 Dec 4 22:41 99-rpi-keyboard.rules '
bootfs » config.txt cat /media/${USER}/bootfs/config.txt && echo <<-'TXT' # For more options and information see # http://rptl.io/configtxt # Some settings may impact device functionality. See link above for details # Uncomment some or all of these to enable the optional hardware interfaces #dtparam=i2c_arm=on #dtparam=i2s=on #dtparam=spi=on # Enable audio (loads snd_bcm2835) dtparam=audio=on # Additional overlays and parameters are documented # /boot/firmware/overlays/README # Automatically load overlays for detected cameras camera_auto_detect=1 # Automatically load overlays for detected DSI displays display_auto_detect=1 # Automatically load initramfs files, if found auto_initramfs=1 # Enable DRM VC4 V3D driver dtoverlay=vc4-kms-v3d max_framebuffers=2 # Don't have the firmware create an initial video= setting in cmdline.txt. # Use the kernel's default instead. disable_fw_kms_setup=1 # Run in 64-bit mode arm_64bit=1 # Disable compensation for displays with overscan disable_overscan=1 # Run as fast as firmware / board allows arm_boost=1 [cm4] # Enable host mode on the 2711 built-in XHCI USB controller. # This line should be removed if the legacy DWC2 controller is required # (e.g. for USB device mode) or if USB support is not required. otg_mode=1 [cm5] dtoverlay=dwc2,dr_mode=host [all] TXT bootfs » cmdline.txt cat /media/${USER}/bootfs/cmdline.txt && echo :' console=serial0,115200 console=tty1 root=PARTUUID=e336fa03-02 rootfstype=ext4 fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles cfg80211.ieee80211_regdom=MY '

SD Card » Pre-Boot

SD Card » Pre-Boot

bootfs » config.txt cat <<'INI' | tee -a /media/${USER}/bootfs/config.txt >/dev/null usb_max_current_enable=1 arm_freq_min=500 gpu_freq_min=500 dtoverlay=dwc2 # Enable Argon NEO 5 NVMe Base dtparam=pciex1 # Set PCIe Speed to Gen 3 dtparam=pciex1_gen=3 INI vcgencmd get_config usb_max_current_enable watch -n 1 vcgencmd measure_clock arm vcgencmd get_config arm_freq_min vcgencmd get_config gpu_freq_min lsmod | grep -E 'dwc2|g_ether' dmesg | grep -E 'dwc2' sudo dtoverlay dwc2 bootfs » cmdline.txt # modules-load=dwc2 cat <<'INI' | tee /media/${USER}/bootfs/cmdline.txt >/dev/null console=serial0,115200 console=tty1 root=PARTUUID=e336fa03-02 rootfstype=ext4 fsck.repair=yes rootwait modules-load=dwc2 quiet splash plymouth.ignore-serial-consoles cfg80211.ieee80211_regdom=MY INI # modules-load=dwc2,g_ether cat <<'INI' | tee /media/${USER}/bootfs/cmdline.txt >/dev/null console=serial0,115200 console=tty1 root=PARTUUID=e336fa03-02 rootfstype=ext4 fsck.repair=yes rootwait modules-load=dwc2,g_ether quiet splash plymouth.ignore-serial-consoles cfg80211.ieee80211_regdom=MY INI # modules-load=dwc2,g_ether # g_ether.host_addr=12:a5:cf:42:92:fd # g_ether.dev_addr=5e:bc:ca:27:92:b1 cat <<'INI' | tee /media/${USER}/bootfs/cmdline.txt >/dev/null console=serial0,115200 console=tty1 root=PARTUUID=e336fa03-02 rootfstype=ext4 fsck.repair=yes rootwait modules-load=dwc2,g_ether quiet splash plymouth.ignore-serial-consoles cfg80211.ieee80211_regdom=MY g_ether.host_addr=12:a5:cf:42:92:fd g_ether.dev_addr=5e:bc:ca:27:92:b1 INI

Playground

Playground
vcgencmd bootloader_version sudo rpi-eeprom-update sudo rpi-update